成人大片

Hot-work is any activity that includes grinding, welding, thermal or oxygen cutting or heating, and other related heat-producing or spark-producing operations, for example welding or other sources of ignition near a hazard.

For the purposes of this information sheet outdoor activities such as 4 wheel driving and harvesting are not hot-work. 听For these activities please refer to the Hazard Management chapter and Off-campus activity FAQ and follow the processes outlined for managing the hazards and eliminating/minimising the risk.

Yes.听 When the hot-work constitutes a fire or explosion hazard then the requirements of the 鈥�Safety in welding and allied processes鈥� apply.

This includes the requirement for:

• any flammable and combustible liquids to be stored in accordance with AS 1940 鈥淭he storage and handling of flammable and combustible liquids鈥�;
• fire extinguishers to be located in accordance with AS 1674.1 (Section 5) 鈥淔ire protection鈥�;
• all provisions of Sections 2 鈥淕eneral precautions鈥� and Section 3 Hazardous areas鈥� to be met, if the hot work is being conducted in a 鈥渉azardous area鈥� (see note below).听 This includes the requirement to appoint a 鈥淩esponsible Officer鈥� (see note below), the nomination of a firewatcher and the completion of a hot-work permit (see Appendix A 鈥淗ot-work 鈥� Permit to Work template鈥� of this FAQ); and
• monitoring to ensure that the requirements of the standard(s) are being met.

For all other hot-work activities in a welding workshop, that are not undertaken in a hazardous area or when the hot work constitutes a fire or explosion hazard, the activity is to managed in accordance with the Hazard Management Handbook chapter and authorised by the Supervisor/person in control of the activity/area prior to commencement.

Note:听 Hazardous area (as described in 鈥淪afety in welding and allied processes鈥�)

An area in which flammable liquids, vapours or gases, combustible liquids, dusts or fibres, or other flammable or explosive substances may be present.听 For additional information on the classification of hazardous areas refer to AS 2430 Part 1: Explosive gas atmospheres; Part 2: Combustible dusts; Part 3: specific occupancies.听 A normally safe area, into which a tank, container or equipment containing flammable combustible liquids, gases or vapours has been brought, may also become a hazardous area.

Note:听 Responsible officer (as described in 鈥淪afety in welding and allied processes鈥�)

A person having a satisfactory knowledge of the fire, explosion and toxicity hazards associated with hot work in hazardous areas and who is adequately trained and experienced in the testing procedures and precautions necessary for the elimination of any risk involved

Prior to the commencement of hot-work a Responsible officer (see note below) is to be appointed to be responsible for:

• the safe completion of the activity (i.e.from start to finish);
• completing a thorough inspection of the site;
• completing a risk assessment, in accordance with the Hazard Management Handbook chapter;
• identifying if there are any flammable or combustible liquids, gases, vapours, dusts, fibres or substances) within 15m from the hot-work, and conducting a test for the presence of flammable gas and flammable vapour above/in/ adjacent to the hot-work in accordance with 鈥淪afety in welding and allied processes鈥�.听
• (The detectors used for the testing are required to comply with 鈥淕eneral requirements for explosion protection of electrical apparatus and systems鈥� and 鈥淧erformance requirements鈥� and the person conducting the test must be skilled in its operation, limitations and maintenance);
• issuing a hot-work permit which complies with the requirements of
• (see an example of a Hot-work permit Appendix A);
• ensuring a firewatcher is appointed and stationed in the area near the hot work for the purpose of safeguarding personnel and equipment where required by the hot-work permit; and
• ensuring the control measures identified on the risk assessment are in place, to prevent any fire, explosion, injury or other danger developing during the performance of the hot-work.

(Note:听 The appointed Responsible officer has the authority to enforce the requirements of 鈥淪afety in welding and allied processes鈥� with respect to employees, contractors and other workers.听 A Responsible officer has the satisfactory knowledge of the fire, explosion and toxicity hazards associated with hot-work in hazardous areas (i.e. any area in which flammable or combustible liquids, vapours, gases, dusts, fibres and/or explosive substances may be present) and is adequately trained and experienced in the testing procedures and precautions necessary for the management of any risk involved.听 The Responsible officer would normally be the person in the local area.听 If there isn鈥檛 a person who is appropriately trained and experienced in this role then the activity should be out-sourced in accordance with the Contractor Safety Management handbook chapter.)

Examples of the hazards that could be present and need to be specifically controlled may include (but not limited to):

• fire hazards (including the presence of flammable or combustible liquids, gases, vapours, dusts, fibres or substances) within 15 m from the hot-work;
• outdoor work near dry grass or bush;
• welding equipment which has not been maintained or does not meet the requirements of 鈥淪afety in welding and allied processes: Electrical.鈥�;
• changing circumstances during the progress of the hot-work (e.g. the outdoor work environment);
• inadequate ventilation in the hot-work area;
• contaminants produced from the hot-work operation;
• radiation (e.g. Electric arc and laser welding emit ultraviolet, visible light and infra-red radiation.听 Depending on the intensity, distance and duration of exposure, the effect of radiation could result in eye disorders and skin burns)
• unsuitable/no fire fighting equipment;
• the hot-work area is not isolated (e.g. others could enter the hot-work area)
• there is the potential for traffic movement in the area of work;
• the space above or below the hot-work area could pose a risk of fire or explosion;
• difficulty in accessing/egressing the hot-work area;
• proximity to electromagnetic fields (Electric arc welding activities produce strong electric and magnet fields.听 It should be noted that electromagnetic fields can disrupt the operation of pacemakers, permanent defibrillators or other medical devices which could cause the heart to stop or slow down);
• exposure to heat;
• exposure to noise (equipment for performing welding can generate varying levels and frequencies of noise);
• exposure to lead (e.g. when welding metals using flux, or welding on stell painted with leaded paints);
• risk of a fall from one level to another;
• inadequate/no Personal Protective Equipment;
• inadequate information/instruction/training provided to the worker;
• no access to equipment/detector to test for the presence of flammable gas and flammable vapour;听
• working in a confined space;
• a total fire ban day.听 (A Total Fire Ban Day may be imposed by the Fire Service at any time of the year restricting the hot work activities, and other activities, you undertake which may result in igniting a fire. For details about what you can and cannot do during a fire ban please see the .听 Restrictions vary across the state.)

Hot-work on or adjacent to fire-protection installations are to be carried out only after consideration has been given to the effect that the hot-work may have on the system and any need for alternative protection.听 It should be noted that smoke and heat detectors may operate by detecting heat, smoke or flames from welding operations.听 Checks should be made as to whether fire protection system should be isolated.听

Please note鈥� where fire protection systems have been isolated, a final check is to be made after the hot work has been completed, to ensure that these systems have been put back on line.

In accordance with the Code of Practice the provision of appropriate information/instruction/training is to be provided having regard to:

• the nature of the work;
• the nature of the risks associated with the work; and
• the control measures implemented.

Any instruction and training should be provided to workers by a proficient or competent/qualified person in accordance with the HSW Handbook chapter Provision of information, instruction and training.

All staff who conduct hot-work need to be identified on the Training Plan and must either have a proficiency (see note below) or qualification (eg. Welder certification, Engineering qualification) before undertaking any hot-work activity. 听The welder and any other person concerned with hot-work activities must also know how to use any fire protection equipment and extinguishing agents (e.g. extinguishers).

(Note: Proficiency = instruction provided on a one-on-one basis or as a group where the operator must demonstrate to their assessor that they are proficient to undertake the task. 听The proficiency is generally mapped against a Safe Operating Procedure, or could be via a log book or series of supervised training sessions.

All workers must:

• be proficient or competent/qualified in accordance with the HSW Handbook chapter Provision of information, instruction and training;
• be authorised by the Responsible officer (see note below);
• be conversant with the control measures on the risk assessment and hot-work permit;
• not work alone;
• know where the fire protection equipment is located and how to use it;
• be provided with any assistance that is considered necessary by the Responsible officer;
• only undertake hot work during the period stated on the hot-work permit;
• obtain a new hot-work permit in the event the hot-work has ceased for a period of more than 2 hrs or extending beyond the currency of the permit;
• understand that ongoing testing and monitoring may be undertaken during the duration of hot-work, if required by the Responsible officer; and
• cease work if requested by the Responsible officer or if the activity is considered unsafe due to a change in the environment.

Note:听 Responsible officer

A staff member, normally in your area of work, who has the knowledge and authority to enforce the requirements of 鈥淪afety in welding and allied processes鈥� with respect to employees, contractors and other workers.听 Including the satisfactory knowledge of the fire, explosion and toxicity hazards associated with hot-work in hazardous areas and who is adequately trained and experienced in the testing procedures and precautions necessary for the elimination of any risk involved.

There are three main types of ventilation, local exhaust, forced dilution and natural dilution you should consider.听

The choice of ventilation system should take into account:

• the amount and type of fumes and contaminants produced
• the proximity and location of the welding process relative to the ventilation system
• the level of ventilation, natural or mechanical, both for the whole workplace and the welding area 鈥� this will also depend on screens and partitions which may restrict cross-flow at the work area
• the proximity of the welder鈥檚 breathing zone to the fume source.

For further information on ventilation systems refer to the SafeWork SA .

In accordance with a firewatcher is required to:

• be stationed in the area near the hot-work;
• not allow hot-work to proceed outside the area specified on the hot-work permit;
• remain on the job unless properly relieved by an authorised person;
• ensure that an appropriate extinguisher is located within 10m of the work area and is used (if required) in accordance with the recommendations of the manufacturer or supplier of the equipment;
• use Personal Protective Equipment (e.g. eye protection to protect against flashes where work involves arc welding, cutting or arc gouging);
• inspect adjoining compartments, if heat transfer is possible;
• maintain a continuous fire watch over the hot-work, paying attention to any changes in weather conditions (e.g. increased wind), whether any actions have been taken that may lead to a hazardous situation in the hot-work area;
• take immediate action to combat any outbreak of fire that may occur and alert the Responsible officer if not the Fire Watcher. 听

Note:听 Firewatching does not consist of periodic checks, but is a continuous and thorough inspection and presence in the area and its vicinity.

Hot-work in confined spaces shall be performed in accordance with 62-77 , 鈥淐onfined Space鈥� and .1 鈥淪afety in welding and allied processes鈥�. 听An additional Permit to enter a Confined Space is also required.

(For further information and guidance on requirements for Confined Space entry, please refer to the Confined Space Information Sheet or local HSW Team.)

All hot-work equipment (e.g. cutting, heating, grinding and welding equipment) must be installed and used in accordance with 鈥淪afety in welding and allied processes鈥� and the other relevant standards referenced within .

The PPE is to be selected to minimise risk by ensuring that:

• the equipment is suitable for the nature of the work;
• it is of suitable size and fit and reasonably comfortable for the worker who is to use or wear it;
• it is maintained, repaired and replaced so that it continues to minimise risk to the worker who uses it, including by ensuring that the equipment is clean and hygienic, and in good working order.

Examples of PPE types, hazards and recommendations are outlined in the .

In the event of a fire emergency all activities should cease immediately and all equipment turned off. 听If it is safe to do so, the fire should be extinguished and any combustibles which could escalate the emergency should be removed. 听Operators should alert the Responsible Officer as soon as possible.听 The Responsible Officer should ensure that a watch is maintained in the area of the fire until it is considered that re-ignition is not possible. 听They should also ensure that no further work is carried out until effective fire equipment is available for use (e.g. Additional extinguishers obtained).

If the fire cannot be extinguished immediately, the Responsible Officer should ensure that the Fire Service are notified (0) 000, in addition to Security (ext 35444) and the HSW Team.

Ensure circumstances contributing to the fire and the results from any subsequent investigation are recorded in accordance with the University鈥檚 on-line Report a safety issue or incident process.

Contractors are to be engaged in accordance with the Contractor Safety Management Handbook chapter.

All contractors must also:

• have a Hot-Work and Permit to Work system in place which meets the requirements of 鈥淪afety in welding and allied processes鈥�; and
• provide a copy of the completed Permit to Work to the University staff member who engaged their services together with all hazard management documentation (e.g. Job Safety Analysis/Risk Assessment).

If the work relates to Construction/capital work, Infrastructure must be contacted:

A Contract/Project Manager will be nominated and will manage the Induction and Hazard Management processes.

For further advice phone

• North Terrace (831) 34008
• Roseworthy Campus (831) 37657
• Waite Campus (831) 37217
• Capital Projects (831) 鈥� 35701 ITDS (831) 33000

(Construction/capital work includes any work carried out in connection with the construction, alteration, conversion, fitting-out, commissioning, renovation, repair, maintenance, refurbishment of a structure).

The use of barbeques (BBQs) is not considered hot work (refer Question 1). However, event planners wanting to use BBQs need to comply with the requirements set out on the Event Safety Management webpage and seek authorisation from Infrastructure for their use on Campus (email Booking and Events Coordinator at facilities.booking@adelaide.edu.au).

If you require further information, please contact a member of the local HSW Team.

Referenced documents within AS 1674.1 can be via the Standards library and include:

听