成人大片

For matters relating to course material or assessment from a specific module, please contact the appropriate lecturer. For general course enquiries, please contact the course co-ordinator.

The primary aim of the course is to provide students with the basic skills and knowledge required to analyse displacement field, stress, strain and failure in deformable solids using analytical solutions and the Finite Element Method. The course develops an understanding of the mechanics of complex practical situations through the establishment and solution of appropriate boundary value problems. At the completion of the course, students should:

Printed Lecture Notes from the Image & Copy Centre (or online via MyUni), and access to MyUni.

• Ugural, A.C. and Fenster, S.K. Advanced Strength and Applied Elasticity, Pearson Education Inc. 1995.
• Cook, R.D. and Young, W.C., Advanced Mechanics of Materials, Prentice-Hall, Inc., 1999.
• Bower, A.F., Advanced Mechanics of Solids at Brown University, .
• Moaveni, S. Finite element analysis: theory and application with ANSYS, Upper Saddle River, NJ: Pearson Prentice Hall, 2008.

• Megson, T.H.G., Aircraft Structures for Engineering Students, Butterworth-Heinemann, 2007.
• Chawla, K. K., Composite Materials-Science and Engineering, Springer, 2nd ed, 1998.
• Curtis, H.D. Fundamentals of Aircraft Structural Analysis, McGraw-Hill, 2002.
• Askeland, D.R. The Science and Engineering of Materials 3rd SI Edition, Chapman and Hall 1999.
• Callister W.D., Materials Science and Engineering An Introduction, 7ed, Wiley, 2007.

All course material plus additional resources will be available through the MyUni system.

Lectures are supported by problem-solving tutorials developing material covered in lectures, FE tutorials and Lab classes.

The required time commitment is 52 hours attendance at lectures and tutorials, approximately 50 hours of revising course material and 40 hours completing assignments.

Module I. Solid Mechanics (A/Prof Andrei Kotousov)

1. Course organization and policies
2. Prerequisites
3. Finite Element Project

1. Stress at a point
2. Principal stresses and principal directions
3. Equilibrium equations
4. Stress transformation equations

1. Strain-displacement equations
2. Normal, shear and volumetric strain
3. Compatibility equations

1. Stress-Strain curve
2. Strain hardening, plasticity and visco-elasticity
3. Generalized Hooke's law
4. Interpretation of elastic constants
5. Solid Mechanics in Engineering Design
6. Examples

1. Fundamental principles of analysis
2. General solution for axisymmetric problems
3. Shrink-fit theory and compound cylinders
4. Spinning disks

1. Elementary models of the theory of plasticity
2. Plasticity action in pressurized cylinder
3. Residual stresses
4. Plasticity action in spinning disks

1. Crack tip fields
2. Linear Fracture Mechanics
3. Fracture Toughness
4. Fracture-Safe design concept

CATCHUP AND REVISION (Time permitting)

Module II. Materials & Structures

1. Introduction
2. Fibre reinforced
3. Principles of reinforcement
4. Mechanical properties
5. Manufacturing routes
6. Other composites
7. Applications

1. Introduction to aerospace structures
2. Mechanics of composites
3. Bending of unsymmetrical beams
4. Shear of thin-walled beams
5. Torsional theory of thin-walled sections
6. Idealised thin-walled sections
7. Stiffened shear panels
8. Shear flow analysis for a skin cutout
9. Thin-plate structural stability

None

The Solid Mechanics module is worth 50% of the total course assessment and the Materials & Structures module worth 50% of the total course assessment

The Final exam will be scheduled in week 15 or 16. Half of the exam will be for the Solid Mechanics module and half will be for the Materials & Structures module.

The following tables are an outline of the assessment for each module of this course. Please note that while every effort has been made to ensure that this information reflects an accurate plan, the coordinator and lecturers have the right to make changes that ensure the continual improvement of the course. Any such changes will be made clear during the lectures and via MyUni.

Solid Mechanics module:

All assignments are due by 5pm on the due date. Details of each task are tabulated below.

Materials & Structures module:

Compulsory attendance at FE tutorials and Lab classes, minimum result required for FE and Lab classes is 50%.

Finite Element (FE) Laboratory

This is a written report on the FE modelling part of the course and will involve problem-solving exercises. The timetable of FE tutorials will be available on MyUni in the beginning of semester.

Experimental Laboratory

This is a report on the experimental study part of the course. The timetable for the lab classes will be available on MyUni in the beginning of semester.

Exam

The examination is intended to assess the student’s knowledge and understanding of the course material. The final examination is open-book.

Solid Mechanics module:

Assignments

These are problem-solving exercises. These problems will be discussed in class in detail before the due date. Example problems with full worked solutions will be considered in class and the solutions of the assignment’s problem will be available on MyUni.

Quizzes

Quizzes are individual in-class assignments and this includes problem-solving exercises to be completed in 45 min with full worked solutions to be available on MyUni.

Materials & Structures module:

Assignments

These are problem-solving exercises covering the topics from this module of the course.

Project

The students are required to carry out a literature review (mini research) on the use of composite materials in aerospace applications. There would be specific topics for students to choose from.

Quizzes will be collected at the end of the in-class tutorials.

All other assignments and reports must be submitted as a hard copy (unless stated otherwise) accompanied by an assessment cover sheet available near the assignment submission area. These must be placed the labelled box on level 2 of Engineering South Building.

Late assignments will be penalised 10% per day. Extensions for assignments and reports will only be given in exceptional circumstances and a case for this with supporting documentation can be made in writing after a lecture or via email. Hard copy assignments will be assessed and returned in 2 weeks of the due date. There will be no opportunities for re-submission of work of unacceptable standard.