成人大片

CHEM ENG 2010 - Process Design II

North Terrace Campus - Semester 1 - 2022

Design of chemical processes starts by properly formulating and solving material and energy balances for whole process flowsheets. In this course, the concepts covered in CHEM ENG 1007 Introduction to Process Engineering are built upon to include multiple units, both reactive and non-reactive systems, single and multiple phases, and steady state and transient processes. More fundamentally, it introduces problem solving strategies used by chemical engineers to solve large and more complex problems by breaking a process down into its components, establishing the relations between known and unknown process variables, assembling the information needed to solve for the unknowns, and finally obtaining the solution using appropriate computational methods. This will be reinforced by undertaking a process design project in small teams. This course is delivered through a combination of online theory lectures, practice workshops, tutorials, and process design sessions.

  • General Course Information
    Course Details
    Course Code CHEM ENG 2010
    Course Process Design II
    Coordinating Unit School of Chemical Eng and Advanced Materials(Ina)
    Term Semester 1
    Level Undergraduate
    Location/s North Terrace Campus
    Units 3
    Contact Up to 6 hours per week
    Available for Study Abroad and Exchange Y
    Prerequisites CHEM ENG 1007
    Assessment Quizzes, mid-Semester test, design project, final examination
    Course Staff

    Course Coordinator: Associate Professor Philip van Eyk

    Course Timetable

    The full timetable of all activities for this course can be accessed from .

  • Learning Outcomes
    Course Learning Outcomes
    On successful completion of this course students will be able to:
      
    1 Use a generalised problem solving strategies to solve a range of material and energy balances
    2 Formulate and solve material balances for steady state and transient processes, single and multiple unit operations, with and without chemical reactions, and for single and multiphase situations.
    3 Formulate and solve energy balances for mechanical energy situations, with and without chemical reactions.
    4 Understand the basics behind economic analysis of a proposed process design
    5 Demonstrate how to use computers (specifically Microsoft Excel) for solving open-ended mass & energy balance for a relatively complex process flowsheet;
    6 Work efficiently and productively in a small team; and
    7 Compose properly formatted progress and final design reports.
      
    The above course learning outcomes are aligned with the Engineers Australia .
    The course is designed to develop the following Elements of Competency: 1.1   1.2   1.3   1.6   2.1   2.2   2.3   2.4   3.2   3.3   3.4   3.5   3.6   

    University Graduate Attributes

    This course will provide students with an opportunity to develop the Graduate Attribute(s) specified below:

    University Graduate Attribute Course Learning Outcome(s)

    Attribute 2: Creative and critical thinking, and problem solving

    Graduates are effective problems-solvers, able to apply critical, creative and evidence-based thinking to conceive innovative responses to future challenges.

    3,5,6

    Attribute 3: Teamwork and communication skills

    Graduates convey ideas and information effectively to a range of audiences for a variety of purposes and contribute in a positive and collaborative manner to achieving common goals.

    5,7,8

    Attribute 4: Professionalism and leadership readiness

    Graduates engage in professional behaviour and have the potential to be entrepreneurial and take leadership roles in their chosen occupations or careers and communities.

    7-8

    Attribute 5: Intercultural and ethical competency

    Graduates are responsible and effective global citizens whose personal values and practices are consistent with their roles as responsible members of society.

    7-8

    Attribute 8: Self-awareness and emotional intelligence

    Graduates are self-aware and reflective; they are flexible and resilient and have the capacity to accept and give constructive feedback; they act with integrity and take responsibility for their actions.

    7-8
  • Learning Resources
    Recommended Resources
    Textbook:
    R.M. Felder, R.W. Rousseau, and L.G. Bullard, Elementary Principles of Chemical Processes, 4th Edition, Wiley, 2018.

    Reference books:
    1. D. M. Himmelblau & J. B. Riggs, “Basic Principles and Calculations in Chemical Engineering”, Prentice-Hall, 8th Edition, 2012.
    2. G.V. Reklaitis, “Introduction to Material and Energy Balances”, Wiley, 1983.
    3. B. E. Poling, J. M. Prausnitz, & J. P. O’Connell, “The Properties of Gases and Liquids”, McGraw-Hill, 5th Edition, 2001.
    4. S. Skogestad, “Chemical and Energy Process Engineering”, CRC Press, 2009.
    5. R. M. Murphy, “Introduction to Chemical Processes: Principles, Analysis, Synthesis”, McGraw-Hill, 2007.
    6. D. Shallcross, “Physical Property Data Book for Engineers and Scientists”, IChemE, 2004.
    7. G.F.C. Rogers & Y.R. Mayhew, “Thermodynamic and Transport Properties of Fluids - SI Units”, Blackwell, 5th Edition, 1995. 8. R.H. Perry & D. Green, “Perry's Chemical Engineers' Handbook”, McGraw-Hill, 7th Edition, 1997.
    Online Learning
    A range of online resources will be provided via MyUni.
  • Learning & Teaching Activities
    Learning & Teaching Modes

    No information currently available.

    Workload

    The information below is provided as a guide to assist students in engaging appropriately with the course requirements.

    Activity Contact hours Workload hours Expected total student workload
    Lectures 0 6 6
    Tutorials 24 24 48
    Design Project 24 36 60
    Practice Workshops 24 0 24
    TOTAL 72 66 138
    Learning Activities Summary
    Topic 1 Introduction and fundamentals of mass balance:
    Presentation of the course, content, and assessment
    Mass balance of single units (refresh of PPE and unsteady state intro)
    Degrees of freedom and 10 steps problem solving strategy

    Topic 2 Multiple units and unsteady state:
    Multiple units process and system boundaries (envelopes)
    Recycle, purge and bypass
    Standard symbols for chemical process diagrams

    Topic 3 Mass balances with reaction:
    Stoichiometry and extent of reaction
    Limiting reagent and molecular balances
    Multiple reaction, yield, and selectivity

    Topic 4 Combustion systems:
    Elemental balances on combustions reactions
    Theoretical and excess air.
    Types of fuel, composition, and analysis

    Topic 5 Single-phase systems:
    Density, ideal gas, and gas mixtures
    Real gases and equations of state
    Compressibility charts and real gas mixtures

    Topic 6 Multiphase systems:
    Single component phase equilibrium
    Gibbs phase rule
    One condensable and multi-component system

    Topic 7 Energy balances and mechanical systems (W):
    The first law of thermodynamics
    Energy balance procedures
    Mechanical energy balances

    Topic 8 Energy balances on non-reactive systems (Q):
    Changes in temperature and changes pressure at constant temperature
    Sensible heat and phase changes (latent heat) calculations
    Psychrometric chart

    Topic 9 Energy balances on reactive systems:
    Heat of reaction and Hess’s law
    Heat of formation and heat of combustion
    Mixing and solutions

    Topic 10 Economic analysis and numerical solutions:
    Fixed capital and operational costs
    Lang factor
    ROI and NPV
    Simulations

    Design Project
    Guided plant design for ammonia production (Haber-Bosch)
    Part 1:
    Block diagram (based on assignment description)
    Mass balances (overall, reactor, mixers, splitters and more)
    Gas phase balances (compression and heat exchange)
    Multiphase balances (separation processes: flash and absorption)
    Part 2:
    Mechanical energy balances (compressors)
    Energy balances non-reactive systems (heat exchange)
    Energy balances reactive systems (reactor)
    Economic analysis (operational cost)
  • Assessment

    The University's policy on Assessment for Coursework Programs is based on the following four principles:

    1. Assessment must encourage and reinforce learning.
    2. Assessment must enable robust and fair judgements about student performance.
    3. Assessment practices must be fair and equitable to students and give them the opportunity to demonstrate what they have learned.
    4. Assessment must maintain academic standards.

    Assessment Summary
    Assessment Task Weighting (%) Individual/ Group Formative/ Summative
    Due (week)*
    Learning outcomes
    Tutorials (x10) 25 Individual Formative Weeks 2-12 1. 2. 3. 4. 5.
    Design Project (Progress report) 8 Group Formative Week 8 1. 2. 3. 4. 5. 6. 7.
    Design Project (Final report) 17 Group Formative Week 13 1. 2. 3. 4. 5. 6. 7.
    Tests (x2) 15 Individual Formative Week 7,12 1. 2. 3. 4.
    Final Exam 40 Individual Summative 1. 2. 3. 4.
    Total 100
    * The specific due date for each assessment task will be available on MyUni.
    Assessment Detail

    No information currently available.

    Submission

    No information currently available.

    Course Grading

    Grades for your performance in this course will be awarded in accordance with the following scheme:

    M10 (Coursework Mark Scheme)
    Grade Mark Description
    FNS   Fail No Submission
    F 1-49 Fail
    P 50-64 Pass
    C 65-74 Credit
    D 75-84 Distinction
    HD 85-100 High Distinction
    CN   Continuing
    NFE   No Formal Examination
    RP   Result Pending

    Further details of the grades/results can be obtained from Examinations.

    Grade Descriptors are available which provide a general guide to the standard of work that is expected at each grade level. More information at Assessment for Coursework Programs.

    Final results for this course will be made available through .

  • Student Feedback

    The University places a high priority on approaches to learning and teaching that enhance the student experience. Feedback is sought from students in a variety of ways including on-going engagement with staff, the use of online discussion boards and the use of Student Experience of Learning and Teaching (SELT) surveys as well as GOS surveys and Program reviews.

    SELTs are an important source of information to inform individual teaching practice, decisions about teaching duties, and course and program curriculum design. They enable the University to assess how effectively its learning environments and teaching practices facilitate student engagement and learning outcomes. Under the current SELT Policy (http://www.adelaide.edu.au/policies/101/) course SELTs are mandated and must be conducted at the conclusion of each term/semester/trimester for every course offering. Feedback on issues raised through course SELT surveys is made available to enrolled students through various resources (e.g. MyUni). In addition aggregated course SELT data is available.

  • Student Support
  • Policies & Guidelines
  • Fraud Awareness

    Students are reminded that in order to maintain the academic integrity of all programs and courses, the university has a zero-tolerance approach to students offering money or significant value goods or services to any staff member who is involved in their teaching or assessment. Students offering lecturers or tutors or professional staff anything more than a small token of appreciation is totally unacceptable, in any circumstances. Staff members are obliged to report all such incidents to their supervisor/manager, who will refer them for action under the university's student鈥檚 disciplinary procedures.

The 成人大片 is committed to regular reviews of the courses and programs it offers to students. The 成人大片 therefore reserves the right to discontinue or vary programs and courses without notice. Please read the important information contained in the disclaimer.