C&ENVENG 7037 - Water Distribution Systems & Design
North Terrace Campus - Semester 1 - 2017
-
General Course Information
Course Details
Course Code C&ENVENG 7037 Course Water Distribution Systems & Design Coordinating Unit School of Civil, Environmental & Mining Eng Term Semester 1 Level Postgraduate Coursework Location/s North Terrace Campus Units 3 Contact Up to 4 hours per week Available for Study Abroad and Exchange N Prerequisites C&ENVENG 2071, C&ENVENG 3079 or equivalent Assessment exam 70%, tutorial, project work 30% Course Staff
Course Coordinator: Emeritus Professor Angus Simpson
Course Coordinator: Professor Angus Simpson
The coordinator and lecturer for this course is:
Professor Angus Simpson
Phone: +61 (08) 8313 5874
Room: N142, Engineering North Building
Email: angus.simpson@adelaide.edu.au
Website: http://www.adelaide.edu.au/directory/angus.simpson
Office hours are provided below
Tutors
Tutors will be available for assistance during the tutorials, computer practical sessions and the design project.
Mr Mengning Qiu
Phone: +61 (08) 8313 3270
Room: N227, Engineering North Building
Email: mengning.qiu@adelaide.edu.au
Office Hours 2016 (starting in Week 2) - Room N142 Engineering North (Professor Simpson)
Monday 11-12noon Office Hour
Thursday 10am-11am Office Hour
Except mid-semester break 2016.
Course Timetable
The full timetable of all activities for this course can be accessed from .
Please note that the course timetable is subject to change, because of public holidays. The final timetable will be confirmed before the beginning of the semester. -
Learning Outcomes
Course Learning Outcomes
On successful completion of this course students will be able to:
1 To develop competency in the engineering fundamentals of (a) the formulation of the underlying governing equations for behaviour of flows and pressures in piped water distribution systems; (b) optimisation of water distribution systems design and operations (c) multi-objective optimisation of water distribution system design for both life cycle cost and life cycle greenhouse gas minimisation and (d) water hammer control in piped systems using air vessels and other water hammer control devices. 2 To develop competency in the analysis, design and optimisation of water distribution systems, in particular, in using computer techniques. 3 To become aware of uncertainty and risk (e.g. in the estimation of peak day water demands and pipe roughnesses) and recognising limitations of engineering approaches and systems. 4 To become aware of the need for sustainable systems and principles of sustainable design by taking into account greenhouse gas emission as a result of construction and pumping operations of water distribution systems. 5 To develop the ability to work and communicate effectively with others in small groups working on assignments and projects in a time-efficient manner – written, oral, listening and time management skills.
The above course learning outcomes are aligned with the Engineers Australia .
The course is designed to develop the following Elements of Competency: 1.1 1.2 1.3 1.4 1.5 1.6 2.1 2.2 2.3 2.4 3.1 3.2 3.5 3.6
University Graduate Attributes
This course will provide students with an opportunity to develop the Graduate Attribute(s) specified below:
University Graduate Attribute Course Learning Outcome(s) Deep discipline knowledge
- informed and infused by cutting edge research, scaffolded throughout their program of studies
- acquired from personal interaction with research active educators, from year 1
- accredited or validated against national or international standards (for relevant programs)
1-5 Critical thinking and problem solving
- steeped in research methods and rigor
- based on empirical evidence and the scientific approach to knowledge development
- demonstrated through appropriate and relevant assessment
1-4 Teamwork and communication skills
- developed from, with, and via the SGDE
- honed through assessment and practice throughout the program of studies
- encouraged and valued in all aspects of learning
5 Career and leadership readiness
- technology savvy
- professional and, where relevant, fully accredited
- forward thinking and well informed
- tested and validated by work based experiences
1-5 Intercultural and ethical competency
- adept at operating in other cultures
- comfortable with different nationalities and social contexts
- able to determine and contribute to desirable social outcomes
- demonstrated by study abroad or with an understanding of indigenous knowledges
5 Self-awareness and emotional intelligence
- a capacity for self-reflection and a willingness to engage in self-appraisal
- open to objective and constructive feedback from supervisors and peers
- able to negotiate difficult social situations, defuse conflict and engage positively in purposeful debate
2 -
Learning Resources
Required Resources
Lecture notes:
It is essential that you aquire a copy of the notes for the course. These notes are from a book prepared by Professor Simpson on "Water Distribution Systems Engineering". The lecture notes are available for purchase from the Unified Online Shop The exam is restricted open book. These notes will be able to be taken into the exam.
You will be expected to read the notes as this is an important source of material from which you will learn. For most assignment and design questions you will need to read thoroughly the appropriate chapter(s) from the notes.
MyUni Resources:
The lectures, tutorials and designs are all critical components of the course. Powerpoint slides for each lecture will be made available. Lecture video recordings will also be made available on MyUni for review. If you miss a lecture it is essential that you review the recording prior to the next lecture.
Powerpoint slides, assignments and design tasks as well as other reference material and videos will be made available electronically via MyUni.Recommended Resources
Chaudhry: Applied Hydraulic, Elger and Roberson: Engineering Fluid Mechanics. 9th Edition
Rouse and Ince: History of Hydraulics
Streeter and Wylie: Fluid Mechanics. SI Version
Wylie and Streeter: Fluid transientsOnline Learning
Online resources (MyUni):Material such as lecture slides, assignments, the design projects, reference material and papers will be provided on MyUni.
Students are expected to regularly check on MyUni for course announcements and utilise the Discussion Board for additional contact.
Other Resources: If required, other relevant resources will be made available in the “Resources” or “Project” sections of the course MyUni site. -
Learning & Teaching Activities
Learning & Teaching Modes
Learning & Teaching Modes
This course uses a number of different teaching and learning approaches (in a set of integrated learning activities) including:
· Lectures (usually two or three 1 hour lectures weekly)
· Problem Solving Tutorials (six throughout the semester)
· Design sessions - computer suites (aproximately 13 hours design/computer suite sessions during the semester)
· Lecture Participation
· Examinations
The lectures are supported and reinforced by the additional teaching modes including tutorials and designs (both formal and informal activities).
This course is aimed to provide you with the opportunity to achieve the course learning objectives in a supportive and motivating context.
The centrepiece of the course are the two Design Projects on water distribution systems. You will learn the fundamental principles/ underlying theory required to complete these designs.Workload
The information below is provided as a guide to assist students in engaging appropriately with the course requirements.
Please note that University guidelines suggest that the average student should spend 48 hours per week to achieve a Credit. Consequently, the total workload for this course is 12 hours per week (144 hours in total over 12 weeks) for an average student to achieve a Credit.
Breakdown of Hours Activity
Contact hours/Private study hours/Total hours (listed below each item)
Lectures
23/0/23
Tutorials/Problem Sets/Designs
17/20/37 hours
Review of previous lecture for Lecture Participation
0/8/8 hours
Design (Part 1) (per person hours)
0/24/24 hours
Design (Part 2) ) (per person hours)
0/24/24 hours
Exam Preparation
0/25/25 hours
Exam
3/0/3 hours
Total
43.0/101/144 hoursLearning Activities Summary
Learning Activities Summary
A summary of the learning activities for this course are given below (L = face-to-face lectures; T = tutorials and design sessions)
A final week by week schedule will be issued closer to the beginning of the semester and will be available on MyUni.
L T Topic
L1 - Introduction/Review
L2 - Solving the Water Distribution System Equations - Graph theory + Q formulation + H formulation-
T1 - Assign. No. W1: Tutorial: Data needs
L3 - Solving the Water Distribution System Equations - LF formulation + Newton solution of Q-equations
L4 - Numerical solution of the water distribution system equations for Q-equations + Two Pipe Problem for Q-equations
T2 - Assign. No. W2: Tutorial: Equation Formulation
L5 - Solving the water distribution system equations - H and LF formulations
L6 - Solving the water distribution system - The Global Gradient Algorithm + Two Pipe Example H-equations
T3 - Assign. No. W2: Tutorial: Equation Formulation
L7 - Solving the water distribution system equations - Two Pipe Problem for H-equations and Two Pipe Problem for LF equations
L8 - Solving the water distribution system equations - the Q+H-equations formulation and the Two Pipe Problem
T4 - Assign. No. W3- Tutorial: Design 1 - Numerical Solution of Pipe Network Equations
L9 - Global Gradient Algorithm method for the two pipe example and Analysis of Efficiency of Solvers
L10 - GGA improvements
T5 - Assign. No. W3- Tutorial: Design 1 - Numerical Solution of Pipe Network Equations
L11 - Pressure regulating valves
L12 - Genetic algorithm optimization of water distribution systems Part #1
T6 - Assign. No. W4 - Tutorial: PRVs
Mid-semester break Week # 1
Mid-semester break Week # 2
L13 - Genetic algorithm optimization of water distribution systems Part #2
L14 - Optimization of pumping using genetic algorithms
T7 - Assign. No. W5 Tutorial: GA by hand
L15 - GA sustainability- Multiobjective optimisation Part #1
L16 - Multiobjective optimisation - Part #2
T8 - Assign. No. W6a- Tutorial: Design 1 - Genetic algorithm design No. 6a
T9 - Assign. No. W6a- Tutorial: Design 1 - Genetic algorithm design No. 6a
L17 - Review of water hammer
L18 - Water hammer Air Vessels Part 1a
T10 - Assign. No. W6a- Tutorial: Design 1 - Genetic algorithm design No. 6a
T11 - Assign. No. W6a- Tutorial: Design 1 - Genetic algorithm design No. 6a
L19 - Water hammer - Air Vessels #1b
L20 - Running Hytran
T12 - Assign. No. W6b- Tutorial: CATS Design 2 - Genetic algorithms versus manual design
T13 - Assign. No. W7- Tutorial: CATS Air vessel Hytran
L21 - Water hammer - Air Vessels #2
L22 - Column separation and flywheels
L23 - Review of Course - Exam overview
T14 - Assign. No. W6b- Tutorial: CATS Design 2 - Genetic algorithms versus manual design
T15 - Assign. No. W6b- Tutorial: CATS Design 2 - Genetic algorithms versus manual design
-
Assessment
The University's policy on Assessment for Coursework Programs is based on the following four principles:
- Assessment must encourage and reinforce learning.
- Assessment must enable robust and fair judgements about student performance.
- Assessment practices must be fair and equitable to students and give them the opportunity to demonstrate what they have learned.
- Assessment must maintain academic standards.
Assessment Summary
Assessment Task Weighting (%) Individual/ Group Formative/ Summative Due (week)* Hurdle criteria Learning outcomes Tutorials (every one to two weeks) 5 Group Summative Weeks 2-12 1. 2. 3. 4. 5. Designs (two) 25 Group Summative Week 5 1. 2. 3. 5. Examination 70 Individual Summative Week 14 Min 40% 1. 2. 3. 4. 5. Total 100
This assessment breakdown is registered as an exemption to the University's . The exemption is related to the Procedures clause(s): 1. a. iiiAssessment Related Requirements
Expected Course Workload
The information below is provided as a guide to assist students in engaging appropriately with the course requirements.
Please note that University guidelines suggest that the average student should spend 48 hours per week to achieve a Credit.
Consequently, the total workload for this course is 12 hours per week (144 hours in total over 12 weeks) for an average student to achieve a Credit.
Group Work
For assessment tasks requiring group work, groups will be partly self selected (for assignments only). Allocation of numbers of students per group will depend on total number of students in the course in a particular year. If there are 4 members per group the following process will be followed. You will pair up with one other person with whom you will work in group work for the entire semester. Pairs will rotate to form a new group of four for each new group work task. All members in a group are expected to contribute equally to the overall task. In cases of perceived unequal contributions to group work, students should come and discuss the matter with the teaching staff.
Hurdle Requirements
In order to pass this course, students must obtain at least:
40% for the exam
If the above requirements are not met, students will receive a 39 F (fail) for this course OR the weighted mark for the course (whichever is lower mark).
Please be aware that you may be eligible for an academic supplementary exam if you fail to meet this requirement. If a student sits a supplementary exam on academic grounds, the final mark will be based on that examination only. Failure to demonstrate a necessary level of knowledge and understanding of the course material in the supplementary exam will result in a fail grade.
Assessment Detail
A. Designs Objectives:
The objective of the Designs is to provide students with the opportunity to apply the course material in a realistic context in order to achieve higher-order learning outcomes.
There will be 3 components to the design including:
. Design 1. numerical methods for solving pipe network equations
. Design 2 (a) manual trial-and error design of a water distribution system using computer simulation and (b) genetic algorithm
optimisation of a water distribution system using a computer software program called “Optimizer ” developed by an Adelaide company called Optimatics Pty Ltd.
B. Assignments
Objectives: The objective of the Assignments is to provide students with the opportunity to apply the course material to problems.
There will be a number of assignments - while working individually or in groups of four (sometimes 3 or 4 if necessary).
C. Examination Objectives:
The objective of an Exam is to provide an independent test of whether students have gained an understanding of the key learning objectives. Details of which course learning objectives are addressed by the Exam are given above.
A 3 hour examination will be held at the end of Semester I. It will be a restricted open book exam.
Notes provided by Prof Simpson for the course may be brought into the examination. This is explicitly restricted to the textbook by Crowe and Prof Simpson's book and Powerpoints of material not in Prof. Simpson's book.
NO OTHER BOOKS OR MATERIAL may be brought into the examination.
Information relating to Fluid Properties will be permitted.
· The design, tutorial solutions and worked problems including solutions to old examination problems, may NOT BE brought into the examination.
A check of the material brought in by each student will be made at the beginning of the examination.
· Use of dictionaries is permitted.
. The use of calculators is permitted. Ensuring the calculator batteries are sufficient for the duration of the examination is the
responsibility of the student.
Supplementary exams awarded on academic grounds will only be given in extraordinary circumstances. If a student sits for a supplementary exam on academic grounds, the final mark will be based on the examination only.Submission
Submission deadlines will be given on each assignment and on the lecture and tutorial schedule.
Details about the submission process for the Homework Exercises will be given at the beginning of the semester and details of the submission process for the Designs will be given in separate handouts.
_____________________________________________________________________________________________________________
All submissions should be accompanied by a signed assessment cover sheet - available at:
http://www.ecms.adelaide.edu.au/civeng/current-students/admin/assessment_cover.pdfCourse Grading
Grades for your performance in this course will be awarded in accordance with the following scheme:
M10 (Coursework Mark Scheme) Grade Mark Description FNS Fail No Submission F 1-49 Fail P 50-64 Pass C 65-74 Credit D 75-84 Distinction HD 85-100 High Distinction CN Continuing NFE No Formal Examination RP Result Pending Further details of the grades/results can be obtained from Examinations.
Grade Descriptors are available which provide a general guide to the standard of work that is expected at each grade level. More information at Assessment for Coursework Programs.
Final results for this course will be made available through .
-
Student Feedback
The University places a high priority on approaches to learning and teaching that enhance the student experience. Feedback is sought from students in a variety of ways including on-going engagement with staff, the use of online discussion boards and the use of Student Experience of Learning and Teaching (SELT) surveys as well as GOS surveys and Program reviews.
SELTs are an important source of information to inform individual teaching practice, decisions about teaching duties, and course and program curriculum design. They enable the University to assess how effectively its learning environments and teaching practices facilitate student engagement and learning outcomes. Under the current SELT Policy (http://www.adelaide.edu.au/policies/101/) course SELTs are mandated and must be conducted at the conclusion of each term/semester/trimester for every course offering. Feedback on issues raised through course SELT surveys is made available to enrolled students through various resources (e.g. MyUni). In addition aggregated course SELT data is available.
-
Student Support
- Academic Integrity for Students
- Academic Support with Maths
- Academic Support with writing and study skills
- Careers Services
- Library Services for Students
- LinkedIn Learning
- Student Life Counselling Support - Personal counselling for issues affecting study
- Students with a Disability - Alternative academic arrangements
-
Policies & Guidelines
This section contains links to relevant assessment-related policies and guidelines - all university policies.
- Academic Credit Arrangements Policy
- Academic Integrity Policy
- Academic Progress by Coursework Students Policy
- Assessment for Coursework Programs Policy
- Copyright Compliance Policy
- Coursework Academic Programs Policy
- Intellectual Property Policy
- IT Acceptable Use and Security Policy
- Modified Arrangements for Coursework Assessment Policy
- Reasonable Adjustments to Learning, Teaching & Assessment for Students with a Disability Policy
- Student Experience of Learning and Teaching Policy
- Student Grievance Resolution Process
-
Fraud Awareness
Students are reminded that in order to maintain the academic integrity of all programs and courses, the university has a zero-tolerance approach to students offering money or significant value goods or services to any staff member who is involved in their teaching or assessment. Students offering lecturers or tutors or professional staff anything more than a small token of appreciation is totally unacceptable, in any circumstances. Staff members are obliged to report all such incidents to their supervisor/manager, who will refer them for action under the university's student鈥檚 disciplinary procedures.
The 成人大片 is committed to regular reviews of the courses and programs it offers to students. The 成人大片 therefore reserves the right to discontinue or vary programs and courses without notice. Please read the important information contained in the disclaimer.