C&ENVENG 2025 - Strength of Materials II
North Terrace Campus - Semester 1 - 2019
-
General Course Information
Course Details
Course Code C&ENVENG 2025 Course Strength of Materials II Coordinating Unit School of Civil, Environmental & Mining Eng Term Semester 1 Level Undergraduate Location/s North Terrace Campus Units 3 Contact Up to 4 hours per week Available for Study Abroad and Exchange Y Prerequisites C&ENVENG 1010 & MATHS 1012 Restrictions Available to BE(Civil & Struct), BE(Mining), BE(Architectural) & associated double degree students only Assessment Exam, assignments, tests/quizzes, active participation/in-class quizzes Course Staff
Course Coordinator: Dr Giang Nguyen
Course Timetable
The full timetable of all activities for this course can be accessed from .
-
Learning Outcomes
Course Learning Outcomes
On successful completion of this course students will be able to:
1 Recongise physical phenomenon in the context of strength of materials 2 Demonstrate an understanding of the structural mechanics theory for deformable bodies 3 Apply structural mechanics of deformable bodies to solve engineering problems 4 Demonstrate an understanding of the relationships between loads, member forces and deformations and material stresses and strains 5 Demonstrate an understanding of the assumptions and limitations of the structural mechanics theory 6 Competence in problem identification, formulation and solution
The above course learning outcomes are aligned with the Engineers Australia .
The course is designed to develop the following Elements of Competency:
University Graduate Attributes
This course will provide students with an opportunity to develop the Graduate Attribute(s) specified below:
University Graduate Attribute Course Learning Outcome(s) Deep discipline knowledge
- informed and infused by cutting edge research, scaffolded throughout their program of studies
- acquired from personal interaction with research active educators, from year 1
- accredited or validated against national or international standards (for relevant programs)
1-6 Critical thinking and problem solving
- steeped in research methods and rigor
- based on empirical evidence and the scientific approach to knowledge development
- demonstrated through appropriate and relevant assessment
2-6 -
Learning Resources
Required Resources
Lecture slides and notes will be uploaded regularly on MyUni.
Lectures will follow the content in “Mechanics of Materials” 8th SI Edition by RC Hibbeler, published by Pearson (2011). Earlier and latest editions can also be used.
Other suitable textbook, Mechanics of Materials by Beer & Johnston, can also be used as references.
Recommended Resources
Course textbook:
“Mechanics of Materials” 8/9th SI Edition by Hibbeler, Prentice Hall, 2011. (Earlier or latest editions can also be used)
Other recommended textbook:
“Mechanics of Materials” 5th SI Edition by Beer, Johnston, DeWolf and Mazurek, McGraw Hill, 2009. (Earlier or latest editions can also be used)Online Learning
All course material including lecture slides, assignments and group project will be made available on MyUni throughout the semester.
MyUni will be used to support the in-class teaching. The Discussion Board in MyUni will provide additional support for students to have discussions related to this course. It is strongly recommended that students use the Discussion Board.
The lecturers will typically be recorded but they should be considered complementary to, rather than a substitute for, attendance. In the event of technical failure it will be the student's responsibility to find an alternative source of information.
Course announcements will be proivded on MyUni regularly throughout the course. It is students' responsibility to check MyUni regularly. -
Learning & Teaching Activities
Learning & Teaching Modes
Teaching for this large class will consist primarily of lectures where the fundamental theory will be presented, followed by examples to illustrate how the theory can be applied to solve practical engineering mechanics problems. Students will develop their understanding of the course content through reading of the textbook, practice problem solving through the tutorial questions and attendance at lectures where problem solving strategies are presented and discussed.
Workload
The information below is provided as a guide to assist students in engaging appropriately with the course requirements.
The information below is provided as a guide to assist students in engaging appropriately with the course requirements.
Activity Contact hours Independent study hours Total Lecturers 36 36 Tutorials 11 22 33 Assignments (x5) 20 20 Quiz (x2) 2 20 22 Exam 3 40 43 Total 154 Learning Activities Summary
The learning activities cover the following 7 lecture series:
Ch. 1 – Stress, Strain and Material Properties
Ch. 2 – Axial Loading
Ch. 3 - Torsion
Ch. 4 – Bending
Ch. 5 – Transverse Shear
Ch. 6 – Transverse Shear and combined loading
Ch. 7 – Transformations of Stress/Strain and failure criteria
Ch. 8 – Deflections of Beams
Ch. 9 - Buckling of ColumnsSpecific Course Requirements
All experiments (tension, compression, torsion and column buckling) are video recorded and will be used in parallel with lecture slides. In particular, calculations based on experimental measurements will be used in class to illustrate the theoretical aspects of all above mentioned tests. Students are not required to attend practical classes, but expected to observe the experiments through these videos and answer questions related to the theory in each experiment. -
Assessment
The University's policy on Assessment for Coursework Programs is based on the following four principles:
- Assessment must encourage and reinforce learning.
- Assessment must enable robust and fair judgements about student performance.
- Assessment practices must be fair and equitable to students and give them the opportunity to demonstrate what they have learned.
- Assessment must maintain academic standards.
Assessment Summary
* The specific due date for each assessment task will be available on MyUni.Assessment Task Weighting (%) Individual/ Group Formative/ Summative Due (week)* Hurdle criteria Learning outcomes Assignments 20 Individual Formative Weeks 2-12 1. 2. 3. 4. 5. 6. Quizzes 15 Individual Summative Week 5 and 8 1. 2. 3. 4. 5. 6. Exam 65 Individual Summative Min 40% 1. 2. 3. 4. 5. 6. Total 100
This assessment breakdown complies with the University's Assessment for Coursework Programs Policy.
This course has a hurdle requirement. Meeting the specified hurdle criteria is a requirement for passing the course.
Assignments:
There will be five assignments throughout the course, each worth 4% of your final mark. These assignments will be submitted, marked and returned regularly throughout the semester. Marks on these assignments will make up 15% of the final subject mark.
Quizzes:
There will be two Quizzes (formative) during the semester, each worth 15% of your final mark. The Quizzes will be closed book, closed note and run under examination conditions. If you miss a Quiz through medical reasons, please see the Course Coordinator. The assessment tasks associated with the Quizzes address course learning objectives 1 and 2.
Final Examination:
The final examination (summative) will cover all the materials covered during the semester and contribute towards 65% of the final mark for the subject. The assessment tasks associated with the Final Exam address course learning objectives 1 and 2.
Assessment Related Requirements
Consistent with School policy, in order to pass the course, students must obtain at least 40% in the examination. If the exam hurdle is not
met students will receive a course result of the lesser of their calculated grade and the nominal grade of 45 (Fail). In addition, and in accordance with Modified arrangements for coursework assessment policy, students must complete all assignments and the group project to be eligible for an Additional Assessment.
Requests for exemption from coursework components will only be considered when presented on an Exemption from Attendance Form. All exemption requests must be made by the end of Week 3 of Semester. Exemptions will not be considered for exams or in-class quizzes.
Intelligible English expression (for all assessments) and legible hand-writing (for exam) are considered to be integral parts of the assessment process, and may affect marks.Assessment Detail
Further details of each assessment will be provided in lectures and/or via MyUni well before the due date.Submission
Digital submissions should be submitted by the appropriate MyUni portal for the particular assessment. Further information will be provided
through the course’s MyUni website.
Late submissions will only be accepted for the projects. There will be a loss of 10% of the marks obtained if the submission is less than 24h late, 20% if the submission is between 24 and 48h late and so on. Extensions will only be granted in special circumstances (e.g. illness) and must be sought for each assessment task individually. Extensions will not be granted less than 24h before the deadline for a given task, with the exception of a medical certificate.Course Grading
Grades for your performance in this course will be awarded in accordance with the following scheme:
M10 (Coursework Mark Scheme) Grade Mark Description FNS Fail No Submission F 1-49 Fail P 50-64 Pass C 65-74 Credit D 75-84 Distinction HD 85-100 High Distinction CN Continuing NFE No Formal Examination RP Result Pending Further details of the grades/results can be obtained from Examinations.
Grade Descriptors are available which provide a general guide to the standard of work that is expected at each grade level. More information at Assessment for Coursework Programs.
Final results for this course will be made available through .
-
Student Feedback
The University places a high priority on approaches to learning and teaching that enhance the student experience. Feedback is sought from students in a variety of ways including on-going engagement with staff, the use of online discussion boards and the use of Student Experience of Learning and Teaching (SELT) surveys as well as GOS surveys and Program reviews.
SELTs are an important source of information to inform individual teaching practice, decisions about teaching duties, and course and program curriculum design. They enable the University to assess how effectively its learning environments and teaching practices facilitate student engagement and learning outcomes. Under the current SELT Policy (http://www.adelaide.edu.au/policies/101/) course SELTs are mandated and must be conducted at the conclusion of each term/semester/trimester for every course offering. Feedback on issues raised through course SELT surveys is made available to enrolled students through various resources (e.g. MyUni). In addition aggregated course SELT data is available.
-
Student Support
- Academic Integrity for Students
- Academic Support with Maths
- Academic Support with writing and study skills
- Careers Services
- Library Services for Students
- LinkedIn Learning
- Student Life Counselling Support - Personal counselling for issues affecting study
- Students with a Disability - Alternative academic arrangements
-
Policies & Guidelines
This section contains links to relevant assessment-related policies and guidelines - all university policies.
- Academic Credit Arrangements Policy
- Academic Integrity Policy
- Academic Progress by Coursework Students Policy
- Assessment for Coursework Programs Policy
- Copyright Compliance Policy
- Coursework Academic Programs Policy
- Intellectual Property Policy
- IT Acceptable Use and Security Policy
- Modified Arrangements for Coursework Assessment Policy
- Reasonable Adjustments to Learning, Teaching & Assessment for Students with a Disability Policy
- Student Experience of Learning and Teaching Policy
- Student Grievance Resolution Process
-
Fraud Awareness
Students are reminded that in order to maintain the academic integrity of all programs and courses, the university has a zero-tolerance approach to students offering money or significant value goods or services to any staff member who is involved in their teaching or assessment. Students offering lecturers or tutors or professional staff anything more than a small token of appreciation is totally unacceptable, in any circumstances. Staff members are obliged to report all such incidents to their supervisor/manager, who will refer them for action under the university's student鈥檚 disciplinary procedures.
The 成人大片 is committed to regular reviews of the courses and programs it offers to students. The 成人大片 therefore reserves the right to discontinue or vary programs and courses without notice. Please read the important information contained in the disclaimer.
